无忧文档

QAIP来料检验

质检部IQC

生产部Prod

金工车间Machining Dept

1游标卡尺/Calliper N/A N/A 2游标卡尺/Calliper N/A N/A 3游标卡尺/Calliper N/A N/A 4游标卡尺/Calliper N/A N/A 5游标卡尺/Calliper N/A N/A 6

游标卡尺/Calliper N/A

N/A 7游标卡尺/Calliper N/A N/A 8游标卡尺/Calliper N/A N/A 9游标卡尺/Calliper N/A N/A 10游标卡尺/Calliper N/A N/A 12游标卡尺/Calliper N/A N/A 13游标卡尺/Calliper N/A N/A 14

游标卡尺/Calliper

N/A

N/A

N/A S-4 Level C=0N/A N/A

目测/Visual

N/A N/A N/A

变频电源Power supply 按批次抽检三台 C=03 sample/lot, C=0N/A N/A 变频电源Power supply 按批次抽检五台 C=05 sample /lot, C=0N/A N/A 变频电源Power supply 按批次抽检五台 C=05 sample /lot, C=0N/A N/A 变频电源Power supply

按批次抽检五台 C=05 sample /lot, C=0N/A N/A 温箱Chamber 按批次抽检三台 C=03 sample/lot, C=0N/A N/A 变频电源Power supply 按批次抽检三台 C=03 sample/lot, C=0N/A N/A 变频电源Power supply 按批次抽检三台 C=03 sample/lot, C=0N/A

N/A

压力测试仪,变频电源Power supply manometer 按批次抽检三台 C=03 sample/lot, C=0N/A N/A

耐电压测试仪Electrical safety

tester

按批次抽检两台 C=03 sample/lot, C=0N/A N/A

目测/Visual

轻微损坏 I级 AQL=1.5严重损坏 I级 AQL=1.0 Level I AQL1.5 minor &

AQL1.0 major

N/A N/A

S-4 Level C=0N/A N/A

尺寸Dimension

性能检验Performance Inspection

检查项目

规范要求

外观

Appearance

N/A 包 装Packing 现品票标示与实物必须一致,包装箱没有破损

Label to be comply with the practical parts and stored in cardboard box+vacumn tray

N/A ;

技术部/Engineer Dept:质检部/Quality Dept:

水深30inch和60inch时马达的电流测试

Motor am draw at 30inch & 60 inch deep water loading N/A

马达风压, 风量和功率测试(53,26,0mm风口)

Air flow rate and pressure test,Power input (53mm,26mm and 0mm orifice)

N/A 马达电气安全性能测试(热态绝缘,漏电电流,高压,接地电阻)/Motor electrical safety test (Insulation resistence-hot,Current leakage,Dielectric Voltage-Withstand, Groung Resistence, refer inspection form.

N/A 马达堵转测试;堵转72小时Locked Rotor Test 72 hours

N/A 马达温度保护开关来料125°C温度可靠性测试Thermal Switch 125°C reliability test

N/A 马达启动电流测试(125%额定电流,3个常温下启动)Motor Starting Current Test

N/A 寿命测试t: -带负载测试72小时

Life test with loading for 72hours N/A 马达噪音测试,1米距离 <105dB

Motor noise test : <105dB @ 1 meter distance N/A 马达温升测试: <130°C

Tempeature raising test <130°C N/A 马达上热保护开关装配良好

Thermal switch well assemblied on motor

装配检验Assembly 试装马达引线端子和开关test to assembly the wires terminal with toggle switch.

N/A 马达质量保证书C.O.C verfication 按照马达的规格书确认供应商提供的质量保证书,确认保证书上的电

压,频率,输入功率,最大真空度,最大风量,最大吸入功率,温

升,振动,噪音,寿命,火花等级,绝缘等级符合马达规格书的要求。

Verify the C.O.C to comply with motor output speicication

N/A 目测/Visual 8N/A Ø4±0.1

N/A

马达上标贴内容正确,马达五金外壳没有刮伤

correct labling, no sctach on metal housing of motor

马达引线没有松动,端子没有松动

verify wires no loose, terminal are tight Ø129.5±0.5N/A Ø135±0.5N/A Ø15±0.5

N/A 137.5±0.5N/A 139.9±0.5N/A Ø115±0.5N/A Ø23.5±0.5N/A 56.5±0.5N/A 128.5±0.5N/A 抽样标准/Sample plan 注塑部

Injection Dept

Ø121±0.5N/A Ø83.4±0.5N/A 测量方法Tools

S-2 Level C=0

电机电器有限公司

品质保证检验计划(QAIP)

客户/Customer:

型号/Model:

图号:

编制日期/Date:2015-03-21更新日期/Update:2015-03-21

操作员/Operator

Inspector:

相关文档
热门文档
评论